Store

Orion-Tr Smart 12/12-30A Dc-Dc Charger

ORI121236120
AU$425.00
VICTRON ORION SMART ISOLATED DC-DC CHARGER 12V-12V 30A • BUILT IN BLUETOOTH FOR EASE OF PROGRAMMING
In stock
1
Product Details

Victron smart isolated DC-DC charger:


Experience professional-level DC to DC charging with the Orion-Tr Smart DC-DC Charger, equipped with built-in Bluetooth for effortless monitoring and programming. Designed for use in dual battery systems in vehicles and boats, this adaptive 3-stage charger ensures that the service battery is properly charged using the (smart) alternator and start battery.

Controlled charging is essential, especially for vehicles with smart alternators or long cable runs that may cause voltage drops. This feature is important in increasing battery life and protecting the alternator in lithium systems where direct charging can cause overloading due to the low impedance of the lithium battery.

The Orion Smart DC-DC Charger also features a built-in engine shutdown detection, preventing the onboard voltage of the vehicle from dropping too low. This detection does not require any intervention in the vehicle system or the installation of a separate motor run sensor or CAN-bus system.

Moreover, the Orion-Tr Smart DC-DC Charger is fully programmable via the VictronConnect app, and can be remotely controlled through a switch. In fixed output mode, the output voltage remains stable, regardless of the load or input voltage fluctuations within the specified range.

Get the ultimate in DC to DC charging with the Orion-Tr Smart DC-DC Charger.

Features:

Bluetooth Smart enabled- Any Bluetooth enabled smart phone, tablet or other device can be used to monitor, to change settings and to update the charger when new software features become available.

Fully programmable- Battery charge algorithm (configurable) or fixed output. Smart alternator compatibility: engine running detection mechanism.

Adaptive 3-stage charge algorithm: bulk – absorption – float- For lead acid batteries it is important that during shallow discharges the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.

For lithium batteries absorption time is fixed, default 2 hours.

Alternatively, a fixed output voltage can be chosen.

Remote on-off- A remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example).

All models are short circuit proof and can be paralleled to increase output current- An unlimited number of units can be connected in parallel.

High temperature protected- The output current will reduce at high ambient temperature.

IP43 protection- When installed with the screw terminals oriented downwards.

Screw terminals- No special tools needed for installation.

*Please note as per page 10 on the Victron manual, 60A circuit protection is required on both sides of the unit (start battery and auxiliary battery). Minimum cable size is 10mm2.


Specifications:

Model:

ORI121236120

Input voltage range:

10 - 17V

Under voltage shut down:

7V

Under voltage restart:

7.5V

Nominal output voltage:

12.2V

Output voltage adjust range:

10 - 15V
Continuous output current at nominal output voltage (40°C):

30A

Maximum output current (10s) at nominal output voltage minus 20%:

40A

Short circuit output current:

60A

Continuous output power at 25°C:

430W

Continuous output power at 40°C:

360W

Efficiency:

87%

Operating temperature range:

-20 to +55°C (derate 3% per °C above 40°C)

DC connection:

Screw terminal
Maximum cable cross-section:
16mm2 (AWG5)
Efficiency:
87%
Weight:
1.8kg
Dimensions (HxWxD):
130 x 186 x 80 mm
Warranty:

5 years

IP Rating:
IP43
Save this product for later